Full telescope
Lid and base can cover most of each other when the item is shallow.

Shipping and Moving Boxes
A telescoping box uses a base and separate lid that slide over one another. The overlap can accommodate a range of product depths and reinforces part of the assembled walls.
From $1.49 per box
Price for 1 box at 16 × 12 × 4–7 in, in B-flute corrugated, with full-color digital print on the outside.
| Quantity | Per box | Total |
|---|---|---|
| 1 | $1.49 | $1.49 |
| 100 | $1.49 | $149.00 |
| 250 | $1.49 | $372.50 |
| 500 | $1.49 | $745.00 |
| 1,000 | $1.49 | $1,490.00 |
| 2,500 | $1.49 | $3,725.00 |
| 5,000 | $1.49 | $7,450.00 |
Overlapping corrugated cartons for frames, long products and stock that shares a footprint across several depths.
More overlap generally gives a firmer connection, while extension reduces overlap and can expose weaker regions. Specify the minimum overlap at the deepest load and choose how the two parts are secured for transport.
Our custom telescoping boxes are part of the shipping and ecommerce boxes range alongside our custom shipping boxes. Compare all 236 custom box types, or see how Custom Boxes makes printed packaging from one box.
Two-piece lid and base · 2PC
The standard construction for custom telescoping boxes is the two-piece lid and base (2PC). A separate lid slides down over a base; made from rigid grayboard or folding board. It suits gifts, apparel and presentation sets.
Lid and base can cover most of each other when the item is shallow.
A shorter lid leaves more of the base visible on closing.
| Box style | Two-piece lid and base (2PC) |
|---|---|
| Strength grades | 32 ECT single wall: 200 psi burst, up to 65 lb (29 kg); 44 ECT single wall: 275 psi burst, up to 95 lb (43 kg); 48 ECT double wall: 275 psi burst, up to 100 lb (45 kg) |
| Print methods | Digital CMYK, Offset litho, Flexographic spot color |
| Finishes for this box | One-color panel print, Orientation marks, Identification panel |
| Minimum order | 1 box per size and artwork |
| Digital proof | Within 24 hours of receiving artwork |
| Production time | 8–12 business days after artwork approval |
| Shipping | Free standard shipping across the US, 3–6 business days, tracked |
| Returns | Free returns within 21 days of delivery |
Every order is cut to your inside dimensions, so treat these sizes as starting points.
| Inside size (L × W × D) | What fits |
|---|---|
| 16 × 12 × 4–7 in | Frames or shallow parts of different depths |
| 24 × 18 × 8–12 in | Larger components with corner restraint |
Measure the item with its end pads and wrap in place. Set it into the inner part and slide the outer piece over it in the direction you plan to use. The parts can fit when empty and bind once a pad pushes a side outward. Check the join at the widest point of the filled sample.
For a long item, look at how far the sections overlap when the deepest product is packed. Mark the range you have tested. A shorter item may need a stop inside rather than more overlap if the customer needs access to one end.
Use the closure planned for transport and move the filled sample from the points staff can reach. Look at where the two parts meet when the carton is held level and when one end is raised. Check whether a label or band shifts over the joint. Keep any printed note away from a face that becomes hidden at a different extension.
Open the sample on a surface long enough to support both pieces. See whether the outer part can slide away without pulling the inner pack out with it. Leave a place for the receiver to hold each section while the item stays supported.
Mark the extension and support positions for each product on a packing drawing. If a picture frame, rod or other item uses the same two parts, try each one independently. Its corners may land near a different part of the overlap. Include any extra pads in the measurements.
Test the shipping label at the shortest and longest positions. Place it on one continuous surface so it does not bridge the opening. Keep the approved pieces with the packing notes so a later change in product length can be checked against the same fit.
Test the carton at maximum extension under handling and compression.
Avoid a label across a moving lid seam.
Fit the inner and outer pieces with their end pads installed, then note where the join lands for each product. Mark which end should rest on the bench when the box is loaded. If the carton is loaded from one end, check whether the other end can be reached without removing tape. Keep a short assembly note with the blanks so staff can match the overlap to the item they are packing.
If your launch date is close, rush production shortens the production time on most corrugated formats. Want to feel the board and finishes first? Order a free sample pack before you commit.
Pricing for custom telescoping boxes starts at $1.49 per box for 1 box at 16 × 12 × 4–7 in, in B-flute corrugated, with full-color digital print on the outside. The listed price is per box, in the standard specification, at any listed quantity. Larger runs, other boards and finishes are quoted.
After you send artwork, a digital proof comes back within 24 hours, and design help on the dieline is free. Production of custom telescoping boxes takes 8–12 business days once the proof is approved. Standard shipping across the US is free and takes 3–6 business days, with tracking.
For production runs in the thousands, see wholesale custom boxes, compare every format on the custom box price list, or request a quote for custom telescoping boxes.